Name: Minute Man SSL-WATER
Brand: Minute Man
SKU: 1035484
Rating: 62 (1 reviews)

manualMinute Man SSL-WATER

SSL-WATER User’s Manual

IMPORTANT: Read all of the instructions before

attempting to install the SSL-WATER leak sensor.

DESCRIPTION

The SSL-WATER sensor is a device, which connects with

SSL-EMD. When water permeates into the sensor cable, the

conductivity enhances the intensity of electric current and the

alarm will be triggered. Through the SNMP-SSL card, the use

can monitor it and receive notifications of the alarms. The

following cable type comes with the water leak sensor:

• Type A: 1m water leak sensor connected to 1.2m cable

APPLICATION

Common usage are areas where mission-critical equipment is

being maintained, including data rooms, data centers, clean

rooms, utility corridors, laboratories, telecommunication

facilities, storage areas, elevator shafts, drip pans unde

wate

-cooled equipment, and many more. The most common

application for water leak detection is under raised floors. It is

common for water leak sensors to be installed under the

raised floor as well as in the ceiling above equipment.

Facilities and equipment that use water-cooled technology

have started to add water leak sensors to provide early

warning of water leaks. The water leak sensor is installed

around the supply and return water lines.

INSTALLATION

1. Loosen the screws on SSL-EMD.

2. Connect the wires of SSL-WATER sensor to the SSL-EMD

larm-1 and/or Alarm-2, and then tighten the screws.

3. Connect the straight-through CAT5 network cable from the

SNMP-SSL card’s RJ45 connector labeled “COM” to the

connector labeled “010101” on the SSL-EMD.

4. Verify that the SNMP-SSL card has a network connection and

is powered on.

5. Check the LED (Power/Status) of SSL-EMD, it will flash ever

5-seconds.

6. Open a Web browser and connect to the SNMP-SSL card.

7. Change the setting of “SSL-EMD Status” from “Disable” to

“Auto” on the EMD Configuration page.

8. Set the status of Alarm-1 and/or Alarm-2 to “Normal Open”.

9. Place the SSL-WATER sensor in the desired location.

10. The installation of the SSL-WATER sensor is complete. See

the SNMP

SSL User

’

s Manual.

LIMITED PRODUCT WARRANTY

Para Systems Inc. (Para Systems) warrants this equipment, when

properly applied and operated within specified conditions, against

faulty materials or workmanship for a period of three years from the

date of original purchase by the end user. For equipment sites within

the United States and Canada, this warranty covers repair o

replacement of defective equipment at the discretion of Para

Systems. Repair will be from the nearest authorized service center.

Replacement parts and warranty labor will be borne by Para Systems.

For equipment located outside of the United States and Canada, Para

Systems only covers faulty parts. Para Systems products repaired

or replaced pursuant to this warranty shall be warranted for the

remaining portion of the warranty that applies to the original product.

This warranty applies only to the original purchaser who must have

properly registered the product within 10 days of purchase.

The warranty shall be void if (a) the equipment is damaged by the

customer, is improperly used, is subjected to an adverse operating

environment, or is operated outside the limits of its electrical

specifications; (b) the equipment is repaired or modified by anyone

other than Para Systems or Para Systems-approved personnel; or (c)

has been used in a manner contrary to the product's operating

manual or other written instructions.

ny technical advice furnished before or after delivery in regard to use

or application of Para Systems’s equipment is furnished without

charge and on the basis that it represents Para Systems’s best

udgment under the circumstances, but it is used at the recipient's

sole risk.

EXCEPT AS PROVIDED HEREIN, PARA SYSTEMS MAKES NO

WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

PARTICULAR PURPOSE. Some states do not permit limitation o

implied warranties; therefore, the aforesaid limitation(s) may not appl

to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL PAR

SYSTEMS BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF

THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE. Specifically, Para Systems is

not liable for any costs, such as lost profits or revenue, loss o

equipment, loss of use of equipment, loss of software, loss of data,

cost of substitutes, claims by third parties, or otherwise. The sole

and exclusive remedy for breach of any warranty, expressed o

implied, concerning Para Systems’s products and the only obligation

of Para Systems hereunder, shall be the repair or replacement o

defective equipment, components, or parts; or, at Para Systems’s

option, refund of the purchase price or substitution with an equivalent

replacement product. This warranty gives you specific legal rights

and you may also have other rights, which vary from state to state.

OBTAINING TECHNICAL ASSISTANCE

Para Systems (Minuteman UPS) Technical Support:

Phone: 1-972-446-7363

Fax: 1-972-446-9011

Web: www.minutemanups.com/support/con_tech2.php

View the manual for the Minute Man SSL-WATER here, for free. This manual comes under the category Humidifiers and has been rated by 1 people with an average of a 6.2. This manual is available in the following languages: English. Do you have a question about the Minute Man SSL-WATER or do you need help? Ask your question here

Need help?

Do you have a question about the Minute Man and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Minute Man owners to provide you with a good answer.

Number of questions: 0